5SHY3545L0009 3BHE009681R0101 GVC750BE101 3BHB013085R0001現貨

我們這里有您急需的停產備件，

優勢現貨，詢不到的，買不到的，請聯系我們！

歡迎來電詢價，我們將會給您滿意的價格！

公司主營進口PLC模塊，可編程控制器，伺服控制系統，和DCS備件等，
例如：ABB、AB、GE， Bently，FOXBORO. MOTOROLA. XYCOM.HONEYWELL.YASKAWA. SIEMENS. SCHNEIDER. REXROTH. YOKOGAWA .KUKA .OVATION .OMRON 等。
尊敬的顧客您好，為了更好的保障您的合法權益，購買前請仔細閱讀以下內容：

1.由于市場波動頻繁，本店所標價格，并非實價，請買家提前咨詢后再拍，感謝支持！

2，本店所售商品均為正品現貨，圖片實物拍攝。分為全新原裝、全新無包裝，工程余貨和二手四種貨品。購買前請聯系客服仔細核對貨品、型號、數量。

3， 本店所售商品保證質量，全新無包裝和二手商品簽收三日質量出現問題均包退換，請放心購買。因買家自己弄錯產品型號、參數或剪腳、上機、錯誤接入電源、錯誤安裝、保管不當、人為損壞等除外。

4，本店所售商品國內順豐包郵，國外運費自理。支持七天內有任何產品質量問題退換貨，過期一切損失請自行承擔。簽收快件前，請先檢查包裹內貨物是否有：破損、缺少、貨物型號和數量不對等，有問題請拒絕簽收并及時與我們聯系。簽收后，一切損失請自行承擔。

5,價格說明 并非原價，以詢價為準。

In the injection molding machine, the most widely used control law is proportional, integral, differential control, referred to as PID control. When the actual parameters of the pressure, speed and temperature of the injection molding machine can not be completely and reliably mastered, or the accurate mathematical model can not be obtained, and other technologies of the control theory are difficult to adopt, the parameters must be determined by experience and on-site debugging. At this time, the application of PID control technology is the most convenient. That is, when we do not fully understand the actual injection pressure, speed, temperature, or can not obtain the above parameters through effective measurement means, the most suitable PID control technology. PID control, there are also PI and PD control in practice. PID control is based on the error of the system, using proportional, integral and differential to calculate the control quantity.

Proportional control is the simplest control method. The output of the controller is proportional to the input error signal. When there is only proportional control, the system output has steady-state error.

In the integral control, the output of the control system is proportional to the integral of the input error signal. For a control system of injection molding machine, if there is steady-state error after entering steady state, it is said that the control system has steady-state error or system with steady-state error for short. In order to eliminate the steady-state error, "integral term" must be introduced into the pressure, speed and temperature control of injection molding machine. The error of the integral term depends on the integral of time. With the increase of time, the integral term will increase. In this way, even if the error is very small, the integral term will increase with the increase of time, which will promote the output of the injection molding machine computer to increase, and further reduce the steady-state error until it is equal to zero. Therefore, the proportional integral (PI) control can make the injection molding machine system into steady state without steady-state error.

In the injection molding machine, the most widely used control law is proportional, integral, differential control, referred to as PID control. When the actual parameters of the pressure, speed and temperature of the injection molding machine can not be completely and reliably mastered, or the accurate mathematical model can not be obtained, and other technologies of the control theory are difficult to adopt, the parameters must be determined by experience and on-site debugging. At this time, the application of PID control technology is the most convenient. That is, when we do not fully understand the actual injection pressure, speed, temperature, or can not obtain the above parameters through effective measurement means, the most suitable PID control technology. PID control, there are also PI and PD control in practice. PID control is based on the error of the system, using proportional, integral and differential to calculate the control quantity.

Proportional control is the simplest control method. The output of the controller is proportional to the input error signal. When there is only proportional control, the system output has steady-state error.

In the integral control, the output of the control system is proportional to the integral of the input error signal. For a control system of injection molding machine, if there is steady-state error after entering steady state, it is said that the control system has steady-state error or system with steady-state error for short. In order to eliminate the steady-state error, "integral term" must be introduced into the pressure, speed and temperature control of injection molding machine. The error of the integral term depends on the integral of time. With the increase of time, the integral term will increase. In this way, even if the error is very small, the integral term will increase with the increase of time, which will promote the output of the injection molding machine computer to increase, and further reduce the steady-state error until it is equal to zero. Therefore, the proportional integral (PI) control can make the injection molding machine system into steady state without steady-state error.